Whirlpool Top-Load Washer Error Codes
Common Whirlpool Cabrio, VMW and newer top-load washer fault codes and troubleshooting information.
Whirlpool Washer Error Code Guide
Whirlpool top-load washer error codes vary by model and control platform. The following codes are commonly found on many Whirlpool Cabrio, VMW and newer top-load washers.
| Error Code | Meaning | What to Check |
|---|---|---|
| F0 E2 | Excessive suds | Too much or incorrect detergent. Use HE detergent. |
| F0 E3 | Overload | Load is too large or heavy. |
| F0 E4 | High water temperature | Check for reversed hot/cold hoses or excessively hot incoming water. |
| F0 E5 | Off-balance load | Redistribute clothes and inspect suspension components. |
| F1 E1 | Main control fault | Check control board, wiring and power supply. |
| F2 E1 | Stuck key or button | Inspect user-interface buttons and control. |
| F2 E3 | Control/UI mismatch | Check for an incorrect or incompatible control or user interface. |
| F3 E1 | Water-level system fault | Inspect pressure hose, pressure sensor and control. |
| F3 E2 | Temperature sensor fault | Check thermistor and associated wiring. |
| F5 E1 | Lid switch fault | Inspect lid switch, lid lock and wiring. |
| F5 E2 | Lid lock fault | Check for an obstruction and inspect the lid-lock assembly. |
| F5 E3 | Lid won't unlock | Inspect lid-lock mechanism, wiring and control. |
| F5 E4 | Lid not opened between cycles | Open and close the lid before starting another cycle. |
| F7 E1 | Basket speed/sensor fault | Check motor, shifter, basket movement and speed sensing system. |
| F7 E5 | Shifter fault | Inspect shift actuator, wiring and mechanical components for binding. |
| F7 E6 | Motor fault | Check motor, motor wiring and control. |
| F7 E7 | Motor unable to reach target speed | Check for a heavy load, binding basket, motor problem or control issue. |
| F8 E1 | No or low water entering washer | Check faucets, inlet hoses, inlet screens and water valves. |
| F8 E3 | Overflow condition | Inspect inlet valve, pressure system and control. |
| F8 E5 | Hot/cold water reversed | Verify the hot and cold inlet hose connections. |
| F9 E1 | Long drain | Check drain pump, drain hose and system for restrictions. |
| Ld / F9 E1 | Long drain | Inspect the drain pump and drain system for restrictions. |
| LF / F8 E1 | Long fill | Check household water supply and washer inlet valves. |
| UL / uL | Unbalanced load | Check load distribution and washer suspension. |
| OL / oL | Overload | Remove some clothing and restart the cycle. |
| SD / Sd | Excessive suds | Check detergent type and quantity. Use HE detergent. |
| HC | Hot/cold reversed | Correct the hot and cold water hose connections. |
| dL | Lid lock error | Inspect lid-lock assembly and wiring. |
| dU | Lid unlock error | Inspect lid-lock assembly, wiring and control. |
Important: Check the Model Number
Whirlpool fault-code definitions and diagnostic procedures can vary significantly between washer platforms.
For example, an F7 E1 fault on one Whirlpool washer may require different diagnostic tests than the same code on another model.
Always verify the complete model number before replacing components.
Where Is the Whirlpool Washer Model Number?
On many Whirlpool top-load washers, the model and serial number label can be found underneath the washer lid or around the opening of the washer cabinet.
Example Whirlpool model numbers include: WTW5057LW0, WTW4816FW3, and WTW8127LC0.
Whirlpool Washer Repair in Central Florida
Restor Electronics provides professional Whirlpool washer troubleshooting and appliance repair service in Ocala, Belleview, Summerfield, Lady Lake, The Villages and surrounding areas.
Whirlpool Washer Showing an Error Code?
Have your washer's complete model number and error code available when requesting service. This helps identify the correct diagnostic procedure for your specific Whirlpool washer.
Request Appliance Repair Return to Home